Automatic tire recycling EPT/tyre shredEPTEPT
The 1st step in tire recycling procession
Hefty obligation body
Hooks and cross pulling die made of forty five# metal, tempered and quenched
Geared up with defense frame steering clear of the risks during doing work
Two sequence: Hydraulic one particular and mechanic one particular
Simple to run and alter spare parts (hooks and cross pulling die)
Slicing tires into parts before shredding
Tiny tire pieces are simpler to method in shredder
Knives made of YG-twenty metal, EPT utilizing time
A single clamping cylinEPTand 1 slicing cylinder
Equipped with a roller system to approach huge tires
The large-ability shredEPTwas EPTly deveXiHu (West Lake) Dis.Hu (West Lake) Dis.ed for direct size reduction of tires into cleanly minimize tire chips, dimensions 50×50 mm. Slicing shafts for the generation of greater tire chips are offered substantial torque at low pace minimize even the strongest tires into parts.
All development qualities are made for ongoing procedure in orEPTto achieve highest throughput prices at least expensive expenses.
Very exact tolerances between the cutting knives create cleanly cut tire chips at reduced energy use.
The cutting knives manufactured of higher good quality alloy steel can be re-sharpened and reused which raises the services existence and minimizes the working charges.
The complete cutting chamber is lined with tough put on plates.
Large doorways permit for effortless access into the cutting chamber.
The shear amongst the two rollers will make tire chips into powders as nicely loosen rubbers, steels and textiles
Roller entire body produced of forged metal
Surface of roller created of alloy metal, welded when worn out
A single flat surface area roller and one particular teethed roller, substantial throughput of powders
Bottom made of solid iron
Crisis stop when overload
Length among the two rollers can be altered.
Challenging equipment EPT
Geared up with screening EPT, magnetic separator and fiber separator, 99% purified rubbers will be obtained.
Finals: 8-30 mesh
Ultimate Solution(5-one hundred twenty mesh tyre powder), As picture:
The exact same time, Tyre powEPTis extensively use in a lot of sector. It can make rubber tile, reclaimed rubber, vehicle portion Ect other individuals.
two-Reclaimed rubber Making Line From Tyre Powder:
one. Dynamic desulfurization tank (1 sets
Dynamic desulfurization tank
two. Open miXiHu (West Lake) Dis.ng mill (you require 2-3 sets)
1. Diameter of roller: 450mm
2. Working duration of roller: 1200mm
3. Pace of entrance roller: 24.26m/min
four. Friction ration of two rollers: one: one.27
five. Max hole: 15mm
six. Potential: twenty five-50kgs
7. Wieght: 2000kgs
eight. Motor EPT: 55KW
nine. Dimension: 6150*2280*2000mm
3. Rubber refiner( one sets)
1. Entrance rolle diameter: 480mm (drum )
2. Rear roller diameter: 612mm (drum)
3. Operating size of roller: 800 mm
4. Front roller linear speed: 22.97m/min
five. Velocity ratio of 2 rollers(entrance/rear): one: one.eighty two
6. MAX Gap: 15mm
seven. Motor EPT: 55KW
8. Dimension: 4700*2100*1480mm
Last EPT(RECLAIMED EPT):
|EPT tire pre-processing , you will get lt fifty*50MM rubber crumb|
|one||Single hook debeader||LS-1200||1||eleven KW|
|two||EPT tyre cutter||WTC-one hundred twenty||one||5.five KW|
|three/4||EPT tyre shredder( with EPT tyre conveyor)||ZPS900||one||61.5 KW|
|Rubber powder processing: you will get 3-eight MM rubber powder,at the same time, independent the fiber and metal wire|
|5||Tyre crusher||XK560||1||seventy five KW|
|six||Massive conveyor equipment||BCL-8||2||two KW|
|seven||Small conveyor equipment||BCL-3||1||1.1 KW|
|eight||Massive Magnet separator||BMS22||1||2.2 KW|
|9||Modest Magnet separator||SMS-one||one||1.one KW|
|ten||Large Shaking display screen||BSS-8||one||7.five KW|
|eleven||Small Shaking display screen||SSS-three||1||three KW|
|12||Fiber separator||FS110||one||11 KW|
|13||Wonderful grinder||XMF420||1||32.4 kw|
|14||Circle shaking display||DIA600||1||2.two kw|